湿式摩擦副滑摩过程温度场分析及实验验证

湿式摩擦副滑摩过程温度场与应力场相互耦合作用,温度场分布受到多种因素影响,其中压力、旋转速度、润滑流量作为湿式摩擦副工作参数对其温度场的影响尤为显著。在理论分析基础上,采用有限元数值模拟分析与实验研究相结合的方法,对摩擦界面温度场时空分布特性进行研究,同时研究界面温度场在摩擦副工作压力、相对转速和润滑流量作用下的变化规律。研究表明:在对偶钢片和摩擦片近外径侧更易出现高温和应力集中区,且对偶钢片相对于摩擦片更易出现温度和应力分布不均匀情况;温度场中高温集中区与应力场中应力集中区相对应,最大温度随着压力增加、相对转速增大、润滑流量减少而显著上升,该结果得到试验结果的验证。     

Performance of natural‐fiber–plastic composites under stress for outdoor applications: Effect of moisture,temperature, and ultraviolet light exposure

The effects of moisture, temperature, and ultraviolet (UV) light on performance of natural‐fiber–plastic composites (NFPC) were assessed. We conducted short‐term tests in the laboratory and long‐term tests under natural exposure and measured changes in mechanical properties and color in samples of the composite. Chemical changes of the composite's materials were measured by X‐ray photoelectron spectroscopy to elucidate the mechanisms of chemical transformations on the material surface. Relative humidity highly affected the modulus of rupture (MOR) and the modulus of elasticity (MOE), and had a greater effect than temperature and UV exposure on performance of the composite. The lightness of the composite was increased by the UV effect in the short‐ and the long‐term tests. The X‐ray photoelectron spectroscopy (XPS) analysis suggested that the composite was protected by the UV absorber. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 2570–2577, 2006     

油管电热清防蜡技术在强水敏油田的应用

江苏油田的庄 2、韦 2油田属强水敏油田 ,采用热 (水 )洗油井和化学清防蜡效果较差 ,两油田每年因洗井造成地层污染影响的产量损失在 5 0 0 0t以上 ,约占油田产量的 4 5 %。根据集肤效应 ,采用油管电热清蜡技术 ,在含水小于 6 0 %、井斜小于 4 0°的油井上可正常使用 ,一般通电加热 4 0～ 80min后 ,油井井口温度能达到 5 0℃左右 ,最高可达到 6 5℃以上 ,连续加热 5～ 6h即可达到清蜡目的 ,电热清蜡为周期 6 0～ 90d。影响电热清蜡主要指标因素是油井的产液量 ,产液量越小 ,所需要的加热电流和加热电压也越小 ,井口温度达到最高值越低 ,清蜡效果越差。试验的 7口井平均年度投入产出比达到 1∶5 ,经济效益和社会效益十分明显。     

CuZnAl形状记忆合金热机械循环滞回曲线与振动衰减特性研究

运用电子万能拉伸试验机、动态数据采集分析仪,测试了CuZnAl形状记忆合金的力-变形滞回曲线和安装有CuZnAl形状记忆合金耗能器框架结构的减振性能.借助透射电镜、X射线衍射仪,分析了CuZnAl形状记忆合金热机械循环过程中显微组织的变化.比较了不同热处理方式、不同相变点的CuZnAl形状记忆合金热机械循环后的滞回曲线面积及减振性能.试验结果表明:CuZnAl形状记忆合金用于框架结构的被动振动控制具有较好的减振性能,同时明显降低框架结构的振动频率.马氏体CuZnAl形状记忆合金耗能器具有较大的耗能能力,热机械循环数十次以后滞回面积亦大幅度减小,但相变点高的CuZnAl形状记忆合金的滞回面积减小幅度较小.     

在油田使用的一种记忆合金温控阀

测量了具有双程记忆效应的Cu-298Zn-4Al(质量分数）合金的L－T曲线，用透射电镜观察了该合金在不同时效温度下的微观组织，计算并分析了该双程记忆合金弹簧的实用参数，以此为依据，设计研制了一种能够在油田使用的定温控制阀门，本阀门结构简单，动作可靠，适合控温精度要求不高且工作环境较恶劣的条件下使用，具有广泛的应用前景。     

Comparative effects of cobalt carboxylates on the thermo‐oxidative degradation of LDPE films

This article reports the effect of three cobalt carboxylates—cobalt stearate (CoSt₃), cobalt palmitate (CoPal₃), and cobalt laurate (CoLau₃)—on the thermo‐oxidative degradation of low‐density polyethylene (LDPE) films prepared by sheeting process. The carboxylates were blended with LDPE in the concentration range of 0.05–0.2% (w/w). The degradation was monitored by techniques such as FTIR spectroscopy, change in the mechanical properties (tensile strength and elongation at break), viscometry, surface electron microscopy, melt flow index measurements, and apparent density measurements. Studies indicate that films containing these additives are highly susceptible to thermo‐oxidative degradation. Oxygen containing functionalities such as carbonyl and vinyl species are generated on the surface of polyethylene because of thermo‐oxidation, as indicated by FTIR studies. This oxidative process is accelerated in the presence of cobalt carboxylates. The degradation of LDPE was found to increase proportionally with concentration as well as with increasing chain length of the cobalt carboxylate, and follow the order CoSt₃ > CoPal₃ > CoLau₃. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3758–3765, 2007     

珍珠粉、珍珠层粉、珍珠母粉的热重及热重动力学

采用热重及热重动力学方法 ,分别研究珍珠粉、珍珠层粉和珍珠母粉的热分解过程及其反应机理。结果表明 ,珍珠粉和珍珠层粉的热分解可分为二个阶段 :第一阶段为 2 50～ 370℃之间 ,失重率约 3% ,反应级数为 1 .6,活化能为 1 0 5～ 1 1 0 k J/ mol属于有机质的热分解 ;第二阶段为 60 0～ 770℃ ,失重率约为 40 % ,反应级数为 1 .3,活化能为 2 80～ 2 90 k J/ mol,属于碳酸钙的分解。珍珠母粉在 2 50～ 370℃之间不存在明显的失重。根据这一现象 ,可以通过热重分析来鉴别珍珠及其制品。     

热化学反应法镁合金陶瓷涂层的制备及性能的影响

采用热化学反应法在镁合金基体上制备陶瓷涂层,并对涂层进行耐磨、耐蚀等性能分析.通过XRD物相分析,涂层中有新相生成.且涂层相对基体耐磨、耐蚀性能均有所提高.     

等离子喷涂纳米ZrO2陶瓷表面涂层的热震性能研究

对比研究了等离子喷涂Y2O3稳定的纳米与微米ZrO2涂层的组织结构及性能。结果表明，两种涂层有不同的相结构；纳米ZrO2涂层组织更加细密，铺展性更好，气孔率较低；两种涂层硬度相近；纳米ZiO2涂层的热震性能明显高于微米ZiO2涂层。     

等离子喷涂纳米ZrO_2陶瓷表面涂层的热震性能研究

对比研究了等离子喷涂Y_2O_3稳定的纳米与微米ZrO_2涂层的组织结构及性能。结果表明,两种涂层有不同的相结构;纳米ZrO_2涂层组织更加细密,铺展性更好,气孔率较低;两种涂层硬度相近;纳米ZrO_2涂层的热震性能明显高于微米ZrO_2涂层。